You don't have the latest HBC installed. The previous version couldn't be moved to the SD card, the current one can.by tueidj - FixMii
Please don't bump three year old threads.by tueidj - Homebrew Applications
There's no homebrew for the wiiu, how do you expect to use cheats?by tueidj - Cheat Codes
We were discussing about priiloader in general, not specifically to this situation.by tueidj - FixMii
IOS62 gives the wiiu transfer tool access to the save files and channels installed on the system, so it can pack them onto an SD card as part of the transfer process.by tueidj - Homebrew General
Make sure the wii's date is set correctly.by tueidj - Homebrew General
If it can launch other titles why can't it launch the HBC title?by tueidj - FixMii
Those applications are not supported by this forum.by tueidj - Getting Started
I didn't say they can't be deleted, I said deleting them will only free up a tiny amount of space because the tools don't do it properly.by tueidj - Getting Started
You can delete the Nintendo channel using data management. You can't delete the news and forecast channels without using dangerous homebrew apps, and there's little point doing so anyway because there aren't any homebrew apps that know how to properly reclaim the space they took up.by tueidj - Getting Started
Apparently you fail at reading too. Thread closed to prevent anyone else from offering pointless advice.by tueidj - Getting Started
Try reading the OP's post again: - The problem is with the hackmii installer, not the exploit being used. 3.3 is too old for the latest installer. - The twilight hack never worked on korean wiis. - This thread is nearly 6 months old.by tueidj - Getting Started
Please stop replying to old posts.by tueidj - Getting Started
Site was down, it's back up now.by tueidj - Getting Started
Those online services have been shut down.by tueidj - Getting Started
Oh wait, wiiu. Go back to the wiiu menu and reorder the wiimotes to make sure the wiiu pro controller isn't controller number 1.by tueidj - Homebrew General
UPDATE IT.by tueidj - Homebrew General
Launch the system menu from priiloader, use letterbomb to reinstall HBC.by tueidj - FixMii
Make sure the wii's date is set correctly. The changes to Nintendo's online services have no relevance.by tueidj - Getting Started
I would strongly advise against that, if you install the korean key on a wii with the latest system menu you will brick it.by tueidj - Getting Started
Please stop replying to old threads with useless information.by tueidj - FixMii
Make sure your wii's date is set correctly.by tueidj - Homebrew General
Blinking is done internally by the wiimote, if you want to do it yourself you have to send reports alternating the LEDs on and off. You only need to store the link key if you plan on always enabling authentication, to avoid sending a link_key_request_negative_reply and then responding to the PIN request (which will cause a new link key to be generated every time). For a non-wii host device thereby tueidj - Hardware
The LEDs blink until you send a report telling them to do something else.by tueidj - Hardware
Try increasing the ACL packet length to at least 256 and num_acl_data_packets to 16. The synchronous data parameters shouldn't matter.by tueidj - Hardware
A basic init sequence is: - hci_reset - hci_read_buffer_size - hci_read_bd_addr - hci_host_buffer_size - hci_write_pin_type(0 = variable) - hci_write_page_timeout - hci_write_scan_enable(2 = page scanning enabled) Additional optional commands (things the wiimote doesn't care about but are good practice): - hci_write_cod - hci_change_local_name "The event code 0xFF is reservedby tueidj - Hardware
Do you use the HCI_read_buffer_size and HCI_host_buffer_size commands as part of the controller initialization? Is flow control left off (by default) or explicitly enabled?by tueidj - Hardware
Have you tested sending/receiving ACL data when connected to something other than a wiimote? Nearly every device supports SDP, for example.by tueidj - Hardware
The versions don't matter. The only thing I can think of that might help is to set the page scan type (HCI_Write_Page_Scan_Type) to 1.by tueidj - Hardware
The CIDs aren't important, the wii's software just counts upwards and this was the second time a wiimote had been synched since the game started. Both of "in MTU" values are translated wrong, there's another one further down (0xB900).by tueidj - Hardware